Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
 
Thread Tools Display Modes
Pressure Test for 19gn Red Dot
Unread 08-11-2017, 06:48 PM   #1
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,670
Thanks: 3,210
Thanked 11,173 Times in 1,763 Posts

Default Pressure Test for 19gn Red Dot

I sent the following three loads to Tom Armburst for testing, a scan of the tests is below. Loads where hand weighted as below:
A. 10ga. Federal hull cut to 2 7/8”, WW 209 primer, 19gr Red Dot, Remington SP-10 wad, 2x .125 card wads and 1 .70 card wad in bottom of wad, 1.125oz # 7 ½ lead shot.
B. 10ga. Remington hull cut to 2 7/8”, WW 209 primer, 19gr Red Dot, Remington SP-10 wad, 3x .125 card wads in bottom of wad, 1.125oz # 7 ½ lead shot.
C. 10ga Cheddite hull cut to 2 7/8", Remington SP-10 wad, 3x .125 card wads in bottom of wad, 1.125oz # 7 ½ lead shot.
THIS IS NOT A RECOMMENDATION FOR INFORMATION ONLY. Pressure higher than I hoped for was hoping for 5200+- equal to black.
Craig Larter
Attached Images
File Type: jpg scan0001.jpg (546.2 KB, 312 views)
Craig Larter is offline   Reply With Quote
Unread 08-11-2017, 07:07 PM   #2
Member
Woodcock survey
PGCA Member
 
Daniel Carter's Avatar

Member Info
 
Join Date: Apr 2015
Posts: 1,020
Thanks: 1,473
Thanked 1,509 Times in 636 Posts

Default

Thank you, have been using this load for about 8 months and have been very happy with it, crows not so much. Glad to know the pressure in that i use all 3.
Daniel Carter is offline   Reply With Quote
The Following 2 Users Say Thank You to Daniel Carter For Your Post:
Unread 08-11-2017, 07:54 PM   #3
Member
J.B. Books
PGCA Member
 
Pete Lester's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 2,956
Thanks: 1,743
Thanked 5,121 Times in 1,439 Posts

Default

Craig thanks for sharing this. I see the pressures and velocities as "period correct" for the short ten with 1 1/8 ounce load and they are great loadings for composite barrel guns and with a powder that has and should be available for a long time to come. I also believe this data shows that if one uses their head good short ten loads have and can be wildcatted. I will add these to 2 7/8" reloading data spreadsheet, very helpful since many of the powders on the existing data are obsolete.
__________________
Progress is the mortal enemy of the Outdoorsman.
Pete Lester is offline   Reply With Quote
The Following User Says Thank You to Pete Lester For Your Post:
Unread 08-11-2017, 08:30 PM   #4
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,396
Thanks: 3,200
Thanked 12,447 Times in 3,322 Posts

Default

Craig, I don't load for Ten, but I do for 12,16&20 so am interested in seeing everyone's data. To what do you attribute the jump in pressure in #2 ?
edgarspencer is offline   Reply With Quote
The Following User Says Thank You to edgarspencer For Your Post:
Unread 08-11-2017, 09:19 PM   #5
Member
Double Lab
PGCA Lifetime
Member
 
Daryl Corona's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 4,639
Thanks: 16,814
Thanked 7,044 Times in 2,687 Posts

Default

My guess would be the Remington hulls.
__________________
Wag more- Bark less.
Daryl Corona is offline   Reply With Quote
Unread 08-12-2017, 06:52 AM   #6
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,670
Thanks: 3,210
Thanked 11,173 Times in 1,763 Posts

Default

The only difference is the remington hulls. The remington and cheddite hulls have similar internal volume but the plastic used on the cheddite hulls is softer more of a low density polyethylene. You will note that I had to add card wads to these loads versus 7625 because the red dot takes up much less room. Remington hulls have a larger rim diameter and will not chamber in my LC smith guns. Not a problem with federal and cheddite. So I plan to standardize on the cheddite hull since they are cheaper and very durable plus I obtain cheddite hulls from my non reloading buddies that shoot RST,s.
Craig Larter is offline   Reply With Quote
The Following 2 Users Say Thank You to Craig Larter For Your Post:
Unread 08-12-2017, 07:42 AM   #7
Member
edgarspencer
PGCA Member
 
edgarspencer's Avatar

Member Info
 
Join Date: Sep 2011
Posts: 6,396
Thanks: 3,200
Thanked 12,447 Times in 3,322 Posts

Default

Thanks, Craig. Hard to believe that the wall section of the Chedite and Federal shells can absorb as much as 800 psi. I'll admit, it's something I Never gave any thought to in 50 years of reloading.
edgarspencer is offline   Reply With Quote
Unread 08-12-2017, 07:59 AM   #8
Member
J.B. Books
PGCA Member
 
Pete Lester's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 2,956
Thanks: 1,743
Thanked 5,121 Times in 1,439 Posts

Default

I have not handled a Cheddite 10ga hull, what is the base wad made of? Federal hulls with their fiber/paper base wads are known for lower pressures.
__________________
Progress is the mortal enemy of the Outdoorsman.
Pete Lester is offline   Reply With Quote
The Following User Says Thank You to Pete Lester For Your Post:
Unread 08-12-2017, 08:31 AM   #9
Member
Woodcock survey
PGCA Member
 
Daniel Carter's Avatar

Member Info
 
Join Date: Apr 2015
Posts: 1,020
Thanks: 1,473
Thanked 1,509 Times in 636 Posts

Default

Cheddite has a plastic base wad.
Daniel Carter is offline   Reply With Quote
Unread 08-12-2017, 09:31 AM   #10
Member
J.B. Books
PGCA Member
 
Pete Lester's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 2,956
Thanks: 1,743
Thanked 5,121 Times in 1,439 Posts

Default

Quote:
Originally Posted by Daniel Carter View Post
Cheddite has a plastic base wad.
I think a better question is why does a Federal hull produce lower pressure with all things being roughly equal, it's the fiber base wad, 89% the pressure of a Remington and 93% the pressure of a Cheditte in this test with Red Dot.
__________________
Progress is the mortal enemy of the Outdoorsman.
Pete Lester is offline   Reply With Quote
The Following User Says Thank You to Pete Lester For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:12 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.