Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
Thread Tools Display Modes
Unread 08-13-2017, 05:21 PM   #21
Member
6pt-Sika
PGCA Lifetime
Member
 
CraigThompson's Avatar

Member Info
 
Join Date: Mar 2011
Posts: 7,906
Thanks: 4,917
Thanked 6,509 Times in 2,998 Posts

Default

Quote:
Originally Posted by Craig Larter View Post
Eric: I think the crimps on my loads look good with no open centers, no wad pressure on the sp-10. I had to add card wads to the red dot load versus 7625 since RD takes up much less room. Craig
I put an overshot card in my REM hull SP-10 wad with 16 gauge card wad in the shot cup and 1 1/4 ounce shot to keep the top flat . Oh yeah that's with 30 grains of SR7625 .
CraigThompson is offline   Reply With Quote
Unread 08-13-2017, 06:24 PM   #22
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,393
Thanks: 2,621
Thanked 9,120 Times in 1,518 Posts

Default

OK I would like try and test Unique for 1 1/8oz low pressure 10ga target loads. I think I will start with 25gr. Hoping for less pressure versus red dot. Opinions?? Craig
Craig Larter is offline   Reply With Quote
Unread 08-13-2017, 08:03 PM   #23
Member
J.B. Books
PGCA Member
 
Pete Lester's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 2,785
Thanks: 1,510
Thanked 4,540 Times in 1,308 Posts

Default

Quote:
Originally Posted by Craig Larter View Post
OK I would like try and test Unique for 1 1/8oz low pressure 10ga target loads. I think I will start with 25gr. Hoping for less pressure versus red dot. Opinions?? Craig
Craig I do not understand your desire to achieve a lower pressure load for the short ten than you have with these tested Red Dot loads. They are period correct loads that will not harm a sound composite barrel gun. Loads with pressures lower than these (especially the Federal hull load) is risking the possibility of squib loads especially in cold weather. When you are in the field it is heartbreaking to have a good shot only to have the shell fail when you pull the trigger. I can attest to these Red Dot loads in the federal hull working well in very cold temps, I use them crow hunting in January - March each year in temps in the low teens.
__________________
Progress is the mortal enemy of the Outdoorsman.
Pete Lester is offline   Reply With Quote
Unread 08-13-2017, 08:09 PM   #24
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,393
Thanks: 2,621
Thanked 9,120 Times in 1,518 Posts

Default

OK Pete I respect your opinion. Thanks fro the input. Craig
Craig Larter is offline   Reply With Quote
Unread 08-13-2017, 08:43 PM   #25
Member
William Davis
PGCA Member

Member Info
 
Join Date: Nov 2011
Posts: 1,159
Thanks: 127
Thanked 754 Times in 410 Posts

Default

If you look at Alliants 12 G data lot of Unique loads for 1 1/8 oz at about the charge weights you mentioned. 12s are not 10s but all are fair amount higher in pressure than the 19 g Red dot 10 g load tested.

When powder was in short supply I tried to work up a 1150 fps 1 1/8 oz Short ten load with Unique. Everything at target velocity left a lot of unburned powder. Found a 23 G Green Dot load that worked, at higher velocity and unburned powder left in the bore. Drop it down to 1150 fps more unburned powder, not as bad as Unique still not very satisfactory.

William
William Davis is offline   Reply With Quote
Unread 08-14-2017, 08:22 AM   #26
Member
Paul Harm
Forum Associate

Member Info
 
Join Date: Nov 2008
Posts: 1,770
Thanks: 44
Thanked 753 Times in 416 Posts

Default

With a little research, I think you'll find that many BP and smokeless loads were as high or even higher than the pressures your loads are showing. Thanks for testing and showing the results. I shoot 19grs/RD and 1oz of shot in a 2 3/4" 10ga shell for clays and it works very well.
__________________
Paul Harm
Paul Harm is offline   Reply With Quote
Visit Paul Harm's homepage!
Unread 08-14-2017, 08:34 AM   #27
Member
6pt-Sika
PGCA Lifetime
Member
 
CraigThompson's Avatar

Member Info
 
Join Date: Mar 2011
Posts: 7,906
Thanks: 4,917
Thanked 6,509 Times in 2,998 Posts

Default

intresting ����
CraigThompson is offline   Reply With Quote
Unread 08-14-2017, 09:58 AM   #28
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 15,019
Thanks: 5,783
Thanked 8,204 Times in 4,438 Posts

Default

As I stated in an earlier post, and has been restated by other posters, the Red Dot loads will not damage any good condition ten gauge and eliminates all cold weather performance problems that you could get with slower powders.
Bill Murphy is offline   Reply With Quote
Unread 08-14-2017, 01:51 PM   #29
Member
charlie cleveland
PGCA Member

Member Info
 
Join Date: Jul 2009
Posts: 12,885
Thanks: 0
Thanked 7,579 Times in 3,904 Posts

Default

it would be hard to find a load better than the 19 grain redot loadwith 1 1/8 ounce or 1 1/16 ounce of lead...its a good squirl load...charlie
charlie cleveland is offline   Reply With Quote
Unread 08-14-2017, 07:50 PM   #30
Member
6pt-Sika
PGCA Lifetime
Member
 
CraigThompson's Avatar

Member Info
 
Join Date: Mar 2011
Posts: 7,906
Thanks: 4,917
Thanked 6,509 Times in 2,998 Posts

Default

I just tried two of the RD 19 gr 1 1/8 ounce loads in the REM hull with three 16 gauge .125 card wads in the bottom of the cup . In my NH that's a rather pleasant load .
CraigThompson is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:01 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2023, Jelsoft Enterprises Ltd.
Copyright İ 1998 - 2023, Parkerguns.org
Copyright İ 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.