Parker Gun Collectors Association Forums  

Go Back   Parker Gun Collectors Association Forums Non-Parker Specific & General Discussions Shotgun Shell Reloading

Notices

Reply
Thread Tools Display Modes
Unread 08-12-2017, 10:01 AM   #11
Member
William Davis
PGCA Member

Member Info
 
Join Date: Nov 2011
Posts: 1,183
Thanks: 141
Thanked 784 Times in 428 Posts

Default

Appreciate your posting this. Thinking about replacing my 23 G Green Dot 1 1/8 oz load, same components . It's a little faster, more than it needs to be, and not a real clean burner. Will load up some of the 19/RD 1 1/8 shoot a round of Clay's and see how I like them.

Question for you guys, seems to me Green Dot is better suited for heavier shot loads. Agree ?

William
William Davis is offline   Reply With Quote
Unread 08-12-2017, 10:15 AM   #12
Member
bob weeman
Forum Associate

Member Info
 
Join Date: Jun 2009
Posts: 232
Thanks: 227
Thanked 189 Times in 83 Posts

Default

I had trouble with Cheddites not chambering in both of my 10's after a couple reloadings. Even after super sizing. It was a rim diameter issue as well. So far Remingtons are working ok. Different lots than your Cheddites I guess?? Or maybe just my guns?
bob weeman is offline   Reply With Quote
Unread 08-12-2017, 10:53 AM   #13
Member
Bill Murphy
PGCA Lifetime
Member Since
Second Grade

Member Info
 
Join Date: Jun 2009
Posts: 16,021
Thanks: 6,416
Thanked 9,342 Times in 4,979 Posts

Default

Regardless of the difference in pressure of these three loads, none of them will damage a well preserved ten gauge. A switch to Green Dot or Unique will lower the pressure, but maybe at the expense of poor cold weather performance. Thanks for sharing this information, Craig.
Bill Murphy is offline   Reply With Quote
Unread 08-12-2017, 12:52 PM   #14
Member
Kevin McCormack
PGCA Lifetime
Member

Member Info
 
Join Date: Jun 2009
Posts: 2,113
Thanks: 1,446
Thanked 3,927 Times in 1,101 Posts

Default

Thanks very much for sharing this data, Craig. I gave up reloading years ago when I became a wealthy government retiree, and a friend of mine opened his own ammo factory. I don't own or shoot a 10 gauge, but both my brothers are fanatics about them. I know they'll be interested in these figures.
Kevin McCormack is offline   Reply With Quote
Unread 08-13-2017, 12:52 AM   #15
Member
6pt-Sika
PGCA Lifetime
Member
 
CraigThompson's Avatar

Member Info
 
Join Date: Mar 2011
Posts: 9,099
Thanks: 6,037
Thanked 8,476 Times in 3,748 Posts

Default

Well if I get an invite to a decent Dove field for the opener I just may carry a 10 with Red Dot 1 1/8 ounce loads of #8 . As well as a 20 gauge VHE . Well that is after I shoot a round of skeet and see how they do in my EH #2 frame .
CraigThompson is offline   Reply With Quote
Unread 08-13-2017, 01:44 PM   #16
Member
Eric Johanen
Forum Associate

Member Info
 
Join Date: Jan 2015
Posts: 113
Thanks: 344
Thanked 73 Times in 40 Posts

Default

CL. how are your crimps with this wad column? How deep are you seating the SP10 wad? I found that using a 16 ga. lubed 1/2 inch fiber filler with a .125 nitro card in the wad cup gives me perfect crimps with no dishing. Without the .125 card I found I had dished crimp with some open centers. I am asking only because your .375 filler is quite a bit shorter than my fiber/nitro card filler combination. I had my 1881 Greener out today on the clays course using both Cheddite and Federal hulls and crushed the clays. No large chips and most were vaporized. The 19 grains of Red Dot with an ounce and a eighth of 7.5 shot works very well. Works nicely with all three hulls. Both my Greener and George T. Abbey(probably a Scott made gun) have laminated steel barrels and the tested pressure ranges are comfortable in these heavy barrels. Neither guns are tightly choked or overly heavy at under 9 pounds. I think of them as over bored heavy 12's. Great guns and great loads.
Eric Johanen is offline   Reply With Quote
Unread 08-13-2017, 02:54 PM   #17
Member
Craig Larter
PGCA Lifetime
Member
 
Craig Larter's Avatar

Member Info
 
Join Date: Nov 2008
Posts: 2,671
Thanks: 3,211
Thanked 11,175 Times in 1,764 Posts

Default

Eric: I think the crimps on my loads look good with no open centers, no wad pressure on the sp-10. I had to add card wads to the red dot load versus 7625 since RD takes up much less room. Craig
Attached Images
File Type: jpg 20170813_134815.jpg (50.0 KB, 5 views)
Craig Larter is offline   Reply With Quote
The Following User Says Thank You to Craig Larter For Your Post:
Unread 08-13-2017, 03:11 PM   #18
Member
charlie cleveland
Forum Associate

Member Info
 
Join Date: Jul 2009
Posts: 12,986
Thanks: 0
Thanked 7,803 Times in 3,968 Posts

Default

good looking crimps...charlie
charlie cleveland is offline   Reply With Quote
Unread 08-13-2017, 03:51 PM   #19
Member
Eric Johanen
Forum Associate

Member Info
 
Join Date: Jan 2015
Posts: 113
Thanks: 344
Thanked 73 Times in 40 Posts

Default

Those are fine crimps. I too use no wad pressure. I suspect it's just the difference in the way our loaders are adjusted. Mine is a MEC Sizemaster. I use Red Dot and SR 7625 for the once and an eighth and SR 4756 for once and a quarter. I have a very good supply of both of the SR powders. Must take down the 16 ga. machine and set up the 10 soon as I have worked my way to a pile of empty hulls. 10 ga. hammer guns are way too much fun!!
Eric Johanen is offline   Reply With Quote
Unread 08-13-2017, 05:57 PM   #20
Member
J.B. Books
PGCA Member
 
Pete Lester's Avatar

Member Info
 
Join Date: Jun 2009
Posts: 2,956
Thanks: 1,743
Thanked 5,123 Times in 1,439 Posts

Default

Quote:
Originally Posted by Eric Johanen View Post
CL. how are your crimps with this wad column? How deep are you seating the SP10 wad? I found that using a 16 ga. lubed 1/2 inch fiber filler with a .125 nitro card in the wad cup gives me perfect crimps with no dishing. Without the .125 card I found I had dished crimp with some open centers. I am asking only because your .375 filler is quite a bit shorter than my fiber/nitro card filler combination. I had my 1881 Greener out today on the clays course using both Cheddite and Federal hulls and crushed the clays. No large chips and most were vaporized. The 19 grains of Red Dot with an ounce and a eighth of 7.5 shot works very well. Works nicely with all three hulls. Both my Greener and George T. Abbey(probably a Scott made gun) have laminated steel barrels and the tested pressure ranges are comfortable in these heavy barrels. Neither guns are tightly choked or overly heavy at under 9 pounds. I think of them as over bored heavy 12's. Great guns and great loads.
Eric FWIW I do about the same as you with the Federal hull and 19gr of Red Dot. I use a 1/2" 16ga fiber filler wad and a piece of a cheerio to achieve a proper folded crimp using the SP-10 wad. I am not sure how Craig is getting a good crimp with a much shorter filler wad column but obviously he is. Here are three random Federal's loaded with 19gr of RD for the soon to start crow season. Thanks again Craig for sharing this information with us.
Attached Images
File Type: jpg 0813171653.jpg (463.8 KB, 4 views)
__________________
Progress is the mortal enemy of the Outdoorsman.
Pete Lester is offline   Reply With Quote
The Following 2 Users Say Thank You to Pete Lester For Your Post:
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:21 AM.

Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Copyright © 1998 - 2024, Parkerguns.org
Copyright © 2004 Design par Megatekno
- 2008 style update 3.7 avec l'autorisation de son auteur par Stradfred.